USB供电高精度Hi - Fi的唱机前置放大器-USB-Po
abstract: a quad, low-noise, op amp and ldo are used to build a stereo preamp with riaa equalization to allow converting signals from a record player (phonograph) to a linear output for digitizing by computer sound cards etc.
a phono preamp is needed for preamplifying and equalizing the analog output of the good old record player. the former hi-fi amplifiers or stereos included a phono input, but at this time it is not very common because the cd player has a linear output and doesn't need linearization. if you still want to play your records or you want to archive lps with a soundcard on your computer you will need this phono preamp. this application is easily powered by +5v the usb port supply. no external power supply, dual supply, or wall cube is needed.
this design idea shows a 3.3v powered phone preamplifier with riaa equalization curve. the advantage is the low power, low voltage single supply solution. it is done with a max4478, a quad, low-noise, rail-to-rail op amp. a small linear regulator, the max8877, regulates the noisy +5v from the usb supply down to +3.3v (see figure 1).
figure 1. +5v usb power supply with +3.3v output.
additionally, the max4478 op amp offers a very high power supply rejection ratio of 120db. this circuit is intended for use the standard moving magnet type phono pickup (see figure 2).
figure 2. one channel phono preamplifier with riaa equalization (courtesy of rod elliott. for more information, see: http://sound.au.com/project06.htm).
the high value capacitors with 100µf, 22µf and 10µc could be tantalum or standard electrolytic caps. the low value capacitors with 82nf and 22nf should be 2.5% tolerance, if obtainable, otherwise you may be able to measure a selection of standard tolerance caps to find those which are closest to the required value. some deviation from the ideal riaa equalization curve will occur if these caps are too far from the designated values (see my test). more important is matching between channels—this should be as accurate as possible.
resistors should be 1% metal film for close tolerance and low noise. this design is done with an active low frequency and a passive high frequency filtering. based on the riaa specification table 1 shows the performance with frequency. there is no rumble filter for frequencies below 20hz integrated. please be careful with 50hz-60hz noise. the application has a high amplification for low frequencies. it is about 60db (1000) for 20hz.
as can be seen from table 1 or figure 3, the accuracy is about 1db. this might be increased if a more accurate capacitor for the high-frequency filtering is used. the gain at 1khz is about 40db (100) so a nominal 5mv cartridge output will give 500mv output. this may be increased if necessary, by increasing the value of the 100k resistor in the second stage.
table 1. frequency response
frequency (hz) test (db) ref (db) error
11,8 61,4
20 59,17 59,3 0,13
40 57,44 57,8 0,36
100 53,63 53,1 -0,58
200 48,52 48,2 -0,32
500 43,12 43,2 0,08
1000 40,83 40,0 -0,83
2000 38,41 37,4 -1,01
5000 33,23 31,8 -1,48
10000 27,82 26,3 -1,52
15000 23,85 22,8 -1,05
20000 21,53 20,4 -1,13
figure 3. frequency response vs. riaa reference.
好易点推全新隐藏式晾衣机，小小设计推动巨大进步
揭秘锂氧电池充电慢的根本原因
涂鸦智能发布最新Matter解决方案，满足全球客户多品类开发需求
基于电场调控层间激子光吸收的超微型光谱仪
常见的三种网络存储技术解析
USB供电高精度Hi - Fi的唱机前置放大器-USB-Po
里程碑式突破！我国量子计算原型机“九章”问世
柔性的未来：打印电子技术全解析
计算机大牛最喜欢的机器学习算法你知道是那些吗
EMC实验室的建设流程
七彩虹发布 iGame VULCAN DDR4 内存，全面升级三星 B-die 颗粒
RFID电子标签：推动未来智能化管理进步
电气控制系统的系统组成
人工智能如何检测出歧视
国防与航空航天是业务重要组成部分,开拓中国国防与航空航天市场策略
3D Rudder推出PSVR专用的脚部运动控制器
三相电路中电动机缺相怎么解决
基于ARM技术处理器到2013年将主宰MID市场
检测电阻放哪最合适？电流检测方法使用说明书
低功耗蓝牙无线网关和外设传感器采用Nordic技术实现可远程操作的家庭自动化网络
a phono preamp is needed for preamplifying and equalizing the analog output of the good old record player. the former hi-fi amplifiers or stereos included a phono input, but at this time it is not very common because the cd player has a linear output and doesn't need linearization. if you still want to play your records or you want to archive lps with a soundcard on your computer you will need this phono preamp. this application is easily powered by +5v the usb port supply. no external power supply, dual supply, or wall cube is needed.
this design idea shows a 3.3v powered phone preamplifier with riaa equalization curve. the advantage is the low power, low voltage single supply solution. it is done with a max4478, a quad, low-noise, rail-to-rail op amp. a small linear regulator, the max8877, regulates the noisy +5v from the usb supply down to +3.3v (see figure 1).
figure 1. +5v usb power supply with +3.3v output.
additionally, the max4478 op amp offers a very high power supply rejection ratio of 120db. this circuit is intended for use the standard moving magnet type phono pickup (see figure 2).
figure 2. one channel phono preamplifier with riaa equalization (courtesy of rod elliott. for more information, see: http://sound.au.com/project06.htm).
the high value capacitors with 100µf, 22µf and 10µc could be tantalum or standard electrolytic caps. the low value capacitors with 82nf and 22nf should be 2.5% tolerance, if obtainable, otherwise you may be able to measure a selection of standard tolerance caps to find those which are closest to the required value. some deviation from the ideal riaa equalization curve will occur if these caps are too far from the designated values (see my test). more important is matching between channels—this should be as accurate as possible.
resistors should be 1% metal film for close tolerance and low noise. this design is done with an active low frequency and a passive high frequency filtering. based on the riaa specification table 1 shows the performance with frequency. there is no rumble filter for frequencies below 20hz integrated. please be careful with 50hz-60hz noise. the application has a high amplification for low frequencies. it is about 60db (1000) for 20hz.
as can be seen from table 1 or figure 3, the accuracy is about 1db. this might be increased if a more accurate capacitor for the high-frequency filtering is used. the gain at 1khz is about 40db (100) so a nominal 5mv cartridge output will give 500mv output. this may be increased if necessary, by increasing the value of the 100k resistor in the second stage.
table 1. frequency response
frequency (hz) test (db) ref (db) error
11,8 61,4
20 59,17 59,3 0,13
40 57,44 57,8 0,36
100 53,63 53,1 -0,58
200 48,52 48,2 -0,32
500 43,12 43,2 0,08
1000 40,83 40,0 -0,83
2000 38,41 37,4 -1,01
5000 33,23 31,8 -1,48
10000 27,82 26,3 -1,52
15000 23,85 22,8 -1,05
20000 21,53 20,4 -1,13
figure 3. frequency response vs. riaa reference.
好易点推全新隐藏式晾衣机，小小设计推动巨大进步
揭秘锂氧电池充电慢的根本原因
涂鸦智能发布最新Matter解决方案，满足全球客户多品类开发需求
基于电场调控层间激子光吸收的超微型光谱仪
常见的三种网络存储技术解析
USB供电高精度Hi - Fi的唱机前置放大器-USB-Po
里程碑式突破！我国量子计算原型机“九章”问世
柔性的未来：打印电子技术全解析
计算机大牛最喜欢的机器学习算法你知道是那些吗
EMC实验室的建设流程
七彩虹发布 iGame VULCAN DDR4 内存，全面升级三星 B-die 颗粒
RFID电子标签：推动未来智能化管理进步
电气控制系统的系统组成
人工智能如何检测出歧视
国防与航空航天是业务重要组成部分,开拓中国国防与航空航天市场策略
3D Rudder推出PSVR专用的脚部运动控制器
三相电路中电动机缺相怎么解决
基于ARM技术处理器到2013年将主宰MID市场
检测电阻放哪最合适？电流检测方法使用说明书
低功耗蓝牙无线网关和外设传感器采用Nordic技术实现可远程操作的家庭自动化网络