[图文]水面高度报警器电路图
this circuit will trigger with any fluid with a resistance under 900k between the maximum separation distance of the probes. let me explain further. the circuit uses a 4050b cmos hex buffer working on a 5 volt supply. all gates are biased off by the 10m resistors connected between ground and buffer input. the common probe the topmost probe above probe 1 in the diagram above is connected to the positive 5 volt supply. if probe 1 is spaced 1 cm away from the common probe and tap water at 25 ?c is detected between the probes (a resistance of 20k) then the top gate is activated and the led 1 will light. similarly if probe 2 at 2 cm distance from the common probe detects water, led 2 will light and so on. switch 1 is used to select which output from the hex buffer will trigger the audible oscillator made from the gates of a cmos 4011b ic.
placement of probes:
as 7 wires are needed for the probe i reccommend the use of 8 way computer ribbon cable. the first two wires may be doubled and act as the common probe wire. each subsequent wire may be cut to required length, if required a couple of millimetres of insulation may be stripped back, though the open cut off wire end should be sufficient to act as the probe. the fluid and distance between probe 6 and the common probe wire must be less than 900k. this is because any voltage below 0.5 volt is detected by the cmos ic as logic 0. a quick potential check using a 900k resistance and the divider formed with the 10m resistor at the input proves this point:
5 x (0.9 / (0.9+10) = 0.41 volt.
as this voltage is below 0.5 volt it is interpreted as a logic 0 and the led will light. if measuring tap water at 25 ?c then the distance between top probe and common may be up to 45 cm apart. for other temperatures and fluids, it is advisable to use an ohmmeter first. when placing the probes the common probe must be the lowest placed probe, as the water level rises, it will first pass probe 1, then 2 and finally probe 6.
Firefly-RK3128开发板UART接口介绍
电源故障之空载电压不正常、频率过高等问题，试试这些方法→
浅析BUCK芯片在电路中的应用及特点
【虹科终端安全案例】Radwell如何有效防止无文件攻击和内存中的威胁？
语音报血压、报警电路
[图文]水面高度报警器电路图
抢自驾商机！丰田和日产车企将采用Sony图像传感器
LoRaWAN的适用领域有哪些？
硅太阳能电池开发的战略方向
传台积电大部分7nm产能已被AMD抢下
索尼即将发布全新的A7000相机性能定位为APS-C画幅机型
光电液位传感器在实现液位检测中的应用
电枢和转子的区别
TCL MiniLED技术又一巅峰应用音画娱乐体验一流
Silicon Labs微处理器在新型动态心脏监测仪中的应用
4月7日韩国首发预定，三星S8或于21日全球上市
无线通信有哪些_无线通信方式
低压差分信号传输模拟交叉点开关SCAN90CP02的特点及应用分析
JEDEC即将发布首个3D IC接口标准
AirPi空气质量传感器的制作
placement of probes:
as 7 wires are needed for the probe i reccommend the use of 8 way computer ribbon cable. the first two wires may be doubled and act as the common probe wire. each subsequent wire may be cut to required length, if required a couple of millimetres of insulation may be stripped back, though the open cut off wire end should be sufficient to act as the probe. the fluid and distance between probe 6 and the common probe wire must be less than 900k. this is because any voltage below 0.5 volt is detected by the cmos ic as logic 0. a quick potential check using a 900k resistance and the divider formed with the 10m resistor at the input proves this point:
5 x (0.9 / (0.9+10) = 0.41 volt.
as this voltage is below 0.5 volt it is interpreted as a logic 0 and the led will light. if measuring tap water at 25 ?c then the distance between top probe and common may be up to 45 cm apart. for other temperatures and fluids, it is advisable to use an ohmmeter first. when placing the probes the common probe must be the lowest placed probe, as the water level rises, it will first pass probe 1, then 2 and finally probe 6.
Firefly-RK3128开发板UART接口介绍
电源故障之空载电压不正常、频率过高等问题，试试这些方法→
浅析BUCK芯片在电路中的应用及特点
【虹科终端安全案例】Radwell如何有效防止无文件攻击和内存中的威胁？
语音报血压、报警电路
[图文]水面高度报警器电路图
抢自驾商机！丰田和日产车企将采用Sony图像传感器
LoRaWAN的适用领域有哪些？
硅太阳能电池开发的战略方向
传台积电大部分7nm产能已被AMD抢下
索尼即将发布全新的A7000相机性能定位为APS-C画幅机型
光电液位传感器在实现液位检测中的应用
电枢和转子的区别
TCL MiniLED技术又一巅峰应用音画娱乐体验一流
Silicon Labs微处理器在新型动态心脏监测仪中的应用
4月7日韩国首发预定，三星S8或于21日全球上市
无线通信有哪些_无线通信方式
低压差分信号传输模拟交叉点开关SCAN90CP02的特点及应用分析
JEDEC即将发布首个3D IC接口标准
AirPi空气质量传感器的制作