简单电力场效应管驱动器是孤立的和DC耦合-Simple Po
abstract: an isolated transformer-driver ic (max845) and small external transformer produce an isolated gate-control signal for a power fet.
designers of power electronic circuits must often drive power switches that feed dc, ac, or power signals to a variety of loads. logic-level electronic circuits always provide the driving signals. in general, however, the power sources and their loads have reference levels different from that of the control circuitry (ground).
an isolated transformer-driver ic (max845) serves as a control-signal generator. the signal is coupled to the gate of the mosfet(s) with a very small transformer, and switched on/off using the ic's shdn input. the resulting gate driver (figure 1) can control power loads continuously on or continuously off, and is relatively fast in switching between on and off. the isolated gate control signal is obtained by rectification in the secondary of t1, with a diode (d5) and transistor (q1) to accelerate turn-off.
figure 1. this transformer-coupled fet driver (a) suits a variety of applications: dc power and load (b); ac power and load (c); and ac power signal and load (d).
the driver is simple and physically small because of its tiny package (an 8-pin mmax) and its high operating frequency (450khz minimum), which in turn allows use of a very small transformer. turn-on and turn-off times for an irf740 mosfet are about 2µs, with a propagation delay of 0.5µs. the capacitance between control-circuit ground and the power circuit being controlled is the primary-to-secondary interwinding capacitance of t1, which can be as low as a few picofarads. that capacitance is important in some applications as a measure of the high-frequency insulation between the power and control sections.
figure 1 illustrates possible circuit configurations for switching dc, power ac, and power signals. a given selection of heat sinking and power devices limits the maximum voltage and current that can be handled. the maximum voltage difference between power circuit and control ground is determined by the maximum voltage specifications of t1's primary/secondary insulation. maximum switching speed is limited by the total gate charge to be switched on the power switching mosfets. similarly, the maximum frequency of the controlled power signals depends on the drain/source capacitance of the mosfets used.
a similar version of this article appeared in the january 19, 2005 issue of ee times planet analog supplement.
国际共识:AI产业化从航母式发展到精准打击
从原理出发，交流异步/永磁同步电动机如何产生动力？
Linux运维必备的13款实用工具
小米申请“电子设备和隐蔽摄像头”新专利
电路设计如何控制远程负载的电压
简单电力场效应管驱动器是孤立的和DC耦合-Simple Po
MAXIMD/A转换器MAX547的工作原理、性能特点和应用分析
实测iPhone 12 Pro屏幕竟不如国产手机
最近各国在战略，生物，能源等科技上的动态
入河排污口选用超声波液位计或雷达流速仪的区别
IBM 陈科典：数字经济时代，在华跨国企业应深挖数据潜能同时超前部署应对数据安全挑战
讲解三相异步电动机振动原因的查找方式
双向可控硅的几大基本要素解析
如何保证数据中心建设预算和时间计划
介绍下自动焊接设备的种类
氮化镓你了解多少
英飞凌CoolSiC肖特基二极管650V G6的性能分析和应用
无线网络安全标准是怎样的
云计算和5G基站拉动PCB及汽车电子快速增长
基于FPGA器件的CCD传感器驱动电路的方案设计
designers of power electronic circuits must often drive power switches that feed dc, ac, or power signals to a variety of loads. logic-level electronic circuits always provide the driving signals. in general, however, the power sources and their loads have reference levels different from that of the control circuitry (ground).
an isolated transformer-driver ic (max845) serves as a control-signal generator. the signal is coupled to the gate of the mosfet(s) with a very small transformer, and switched on/off using the ic's shdn input. the resulting gate driver (figure 1) can control power loads continuously on or continuously off, and is relatively fast in switching between on and off. the isolated gate control signal is obtained by rectification in the secondary of t1, with a diode (d5) and transistor (q1) to accelerate turn-off.
figure 1. this transformer-coupled fet driver (a) suits a variety of applications: dc power and load (b); ac power and load (c); and ac power signal and load (d).
the driver is simple and physically small because of its tiny package (an 8-pin mmax) and its high operating frequency (450khz minimum), which in turn allows use of a very small transformer. turn-on and turn-off times for an irf740 mosfet are about 2µs, with a propagation delay of 0.5µs. the capacitance between control-circuit ground and the power circuit being controlled is the primary-to-secondary interwinding capacitance of t1, which can be as low as a few picofarads. that capacitance is important in some applications as a measure of the high-frequency insulation between the power and control sections.
figure 1 illustrates possible circuit configurations for switching dc, power ac, and power signals. a given selection of heat sinking and power devices limits the maximum voltage and current that can be handled. the maximum voltage difference between power circuit and control ground is determined by the maximum voltage specifications of t1's primary/secondary insulation. maximum switching speed is limited by the total gate charge to be switched on the power switching mosfets. similarly, the maximum frequency of the controlled power signals depends on the drain/source capacitance of the mosfets used.
a similar version of this article appeared in the january 19, 2005 issue of ee times planet analog supplement.
国际共识:AI产业化从航母式发展到精准打击
从原理出发，交流异步/永磁同步电动机如何产生动力？
Linux运维必备的13款实用工具
小米申请“电子设备和隐蔽摄像头”新专利
电路设计如何控制远程负载的电压
简单电力场效应管驱动器是孤立的和DC耦合-Simple Po
MAXIMD/A转换器MAX547的工作原理、性能特点和应用分析
实测iPhone 12 Pro屏幕竟不如国产手机
最近各国在战略，生物，能源等科技上的动态
入河排污口选用超声波液位计或雷达流速仪的区别
IBM 陈科典：数字经济时代，在华跨国企业应深挖数据潜能同时超前部署应对数据安全挑战
讲解三相异步电动机振动原因的查找方式
双向可控硅的几大基本要素解析
如何保证数据中心建设预算和时间计划
介绍下自动焊接设备的种类
氮化镓你了解多少
英飞凌CoolSiC肖特基二极管650V G6的性能分析和应用
无线网络安全标准是怎样的
云计算和5G基站拉动PCB及汽车电子快速增长
基于FPGA器件的CCD传感器驱动电路的方案设计