FPGA简单门电路怎么实现？
1. verilog实现基本门电路
verilog实现反相器，2输入与门、2输入或门、2输入与非门、2输入或非门、2输入异或门、2输入同或门；
撰写仿真程序，对实现进行仿真测试；
将仿真后的verilog代码进行综合与实现，并下载到basys3上验证；
2. verilog实现2选1mux
撰写仿真程序，对其进行测试；
将仿真后的verilog代码进行综合与实现，并下载到basys3上验证；
2.
led［0］ sw［0］ sw［1］实现2输入与门
led［2］ sw［2］ sw［3］实现2输入或门
led［4］ sw［4］ sw［5］实现2输入与非门
led［6］ sw［6］ sw［7］实现2输入或非门
led［8］ sw［8］ sw［9］实现2输入异或门
led［10］ sw［10］ sw［11］实现2输入同或门
led［12］ sw［12］实现反相器
led［13］ sw［13］ sw［14］ sw［15］实现2选1mux
3.实现模块
module fpga001（
input ［15:0］ sw，
output ［13:0］ led
）;
assign led［0］ = sw［0］ & sw［1］;
assign led［2］ = sw［2］ | sw［3］;
assign led［4］ = ~（sw［4］ & sw［5］）;
assign led［6］ = ~（sw［6］ | sw［7］）;
assign led［8］ = （sw［8］ & （~sw［9］）） | （~sw［8］ & sw［9］）;
assign led［10］ = ~（（sw［10］ & （~sw［11］）） | （~sw［10］ & sw［11］））;
assign led［12］ = ~sw［12］;
assign led［13］ = ~sw［13］ & sw［14］ | sw［13］ & sw［15］;
endmodule
4.测试模块
module fd;
reg［15:0］ w;
wire［13:0］ l;
fpga001 f（w， l）;
initial
begin
w = 16‘b0;
#10 w = 16’b0010010101010101;
#10 w = 16‘b0101101010101010;
#10 w = 16’b0110010101010101;
#10 w = 16‘b1001101010101010;
#10 w = 16’b1010010101010101;
#10 w = 16‘b1111101010101010;
#20 $finish;
end
initial
begin
$monitor（$time， “led = %b”， w）;
end
endmodule
5.引脚分布图
## this file is a general .xdc for the basys3 rev b board
## to use it in a project：
## - uncomment the lines corresponding to used pins
## - rename the used ports （in each line， after get_ports） according to the top level signal names in the project
## clock signal
#set_property package_pin w5 ［get_ports clk］
#set_property iostandard lvcmos33 ［get_ports clk］
#create_clock -add -name sys_clk_pin -period 10.00 -waveform {0 5} ［get_ports clk］
## switches
set_property package_pin v17 ［get_ports {sw［0］}］
set_property iostandard lvcmos33 ［get_ports {sw［0］}］
set_property package_pin v16 ［get_ports {sw［1］}］
set_property iostandard lvcmos33 ［get_ports {sw［1］}］
set_property package_pin w16 ［get_ports {sw［2］}］
set_property iostandard lvcmos33 ［get_ports {sw［2］}］
set_property package_pin w17 ［get_ports {sw［3］}］
set_property iostandard lvcmos33 ［get_ports {sw［3］}］
set_property package_pin w15 ［get_ports {sw［4］}］
set_property iostandard lvcmos33 ［get_ports {sw［4］}］
set_property package_pin v15 ［get_ports {sw［5］}］
set_property iostandard lvcmos33 ［get_ports {sw［5］}］
set_property package_pin w14 ［get_ports {sw［6］}］
set_property iostandard lvcmos33 ［get_ports {sw［6］}］
set_property package_pin w13 ［get_ports {sw［7］}］
set_property iostandard lvcmos33 ［get_ports {sw［7］}］
set_property package_pin v2 ［get_ports {sw［8］}］
set_property iostandard lvcmos33 ［get_ports {sw［8］}］
set_property package_pin t3 ［get_ports {sw［9］}］
set_property iostandard lvcmos33 ［get_ports {sw［9］}］
set_property package_pin t2 ［get_ports {sw［10］}］
set_property iostandard lvcmos33 ［get_ports {sw［10］}］
set_property package_pin r3 ［get_ports {sw［11］}］
set_property iostandard lvcmos33 ［get_ports {sw［11］}］
set_property package_pin w2 ［get_ports {sw［12］}］
set_property iostandard lvcmos33 ［get_ports {sw［12］}］
set_property package_pin u1 ［get_ports {sw［13］}］
set_property iostandard lvcmos33 ［get_ports {sw［13］}］
set_property package_pin t1 ［get_ports {sw［14］}］
set_property iostandard lvcmos33 ［get_ports {sw［14］}］
set_property package_pin r2 ［get_ports {sw［15］}］
set_property iostandard lvcmos33 ［get_ports {sw［15］}］
## leds
set_property package_pin u16 ［get_ports {led［0］}］
set_property iostandard lvcmos33 ［get_ports {led［0］}］
set_property package_pin e19 ［get_ports {led［1］}］
set_property iostandard lvcmos33 ［get_ports {led［1］}］
set_property package_pin u19 ［get_ports {led［2］}］
set_property iostandard lvcmos33 ［get_ports {led［2］}］
set_property package_pin v19 ［get_ports {led［3］}］
set_property iostandard lvcmos33 ［get_ports {led［3］}］
set_property package_pin w18 ［get_ports {led［4］}］
set_property iostandard lvcmos33 ［get_ports {led［4］}］
set_property package_pin u15 ［get_ports {led［5］}］
set_property iostandard lvcmos33 ［get_ports {led［5］}］
set_property package_pin u14 ［get_ports {led［6］}］
set_property iostandard lvcmos33 ［get_ports {led［6］}］
set_property package_pin v14 ［get_ports {led［7］}］
set_property iostandard lvcmos33 ［get_ports {led［7］}］
set_property package_pin v13 ［get_ports {led［8］}］
set_property iostandard lvcmos33 ［get_ports {led［8］}］
set_property package_pin v3 ［get_ports {led［9］}］
set_property iostandard lvcmos33 ［get_ports {led［9］}］
set_property package_pin w3 ［get_ports {led［10］}］
set_property iostandard lvcmos33 ［get_ports {led［10］}］
set_property package_pin u3 ［get_ports {led［11］}］
set_property iostandard lvcmos33 ［get_ports {led［11］}］
set_property package_pin p3 ［get_ports {led［12］}］
set_property iostandard lvcmos33 ［get_ports {led［12］}］
set_property package_pin n3 ［get_ports {led［13］}］
set_property iostandard lvcmos33 ［get_ports {led［13］}］
set_property package_pin p1 ［get_ports {led［14］}］
set_property iostandard lvcmos33 ［get_ports {led［14］}］
set_property package_pin l1 ［get_ports {led［15］}］
set_property iostandard lvcmos33 ［get_ports {led［15］}］
##7 segment display
#set_property package_pin w7 ［get_ports {seg［0］}］
#set_property iostandard lvcmos33 ［get_ports {seg［0］}］
#set_property package_pin w6 ［get_ports {seg［1］}］
#set_property iostandard lvcmos33 ［get_ports {seg［1］}］
#set_property package_pin u8 ［get_ports {seg［2］}］
#set_property iostandard lvcmos33 ［get_ports {seg［2］}］
#set_property package_pin v8 ［get_ports {seg［3］}］
#set_property iostandard lvcmos33 ［get_ports {seg［3］}］
#set_property package_pin u5 ［get_ports {seg［4］}］
#set_property iostandard lvcmos33 ［get_ports {seg［4］}］
#set_property package_pin v5 ［get_ports {seg［5］}］
#set_property iostandard lvcmos33 ［get_ports {seg［5］}］
#set_property package_pin u7 ［get_ports {seg［6］}］
#set_property iostandard lvcmos33 ［get_ports {seg［6］}］
#set_property package_pin v7 ［get_ports dp］
#set_property iostandard lvcmos33 ［get_ports dp］
#set_property package_pin u2 ［get_ports {an［0］}］
#set_property iostandard lvcmos33 ［get_ports {an［0］}］
#set_property package_pin u4 ［get_ports {an［1］}］
#set_property iostandard lvcmos33 ［get_ports {an［1］}］
#set_property package_pin v4 ［get_ports {an［2］}］
#set_property iostandard lvcmos33 ［get_ports {an［2］}］
#set_property package_pin w4 ［get_ports {an［3］}］
#set_property iostandard lvcmos33 ［get_ports {an［3］}］
##buttons
#set_property package_pin u18 ［get_ports btnc］
#set_property iostandard lvcmos33 ［get_ports btnc］
#set_property package_pin t18 ［get_ports btnu］
#set_property iostandard lvcmos33 ［get_ports btnu］
#set_property package_pin w19 ［get_ports btnl］
#set_property iostandard lvcmos33 ［get_ports btnl］
#set_property package_pin t17 ［get_ports btnr］
#set_property iostandard lvcmos33 ［get_ports btnr］
#set_property package_pin u17 ［get_ports btnd］
#set_property iostandard lvcmos33 ［get_ports btnd］
##pmod header ja
##sch name = ja1
#set_property package_pin j1 ［get_ports {ja［0］}］
#set_property iostandard lvcmos33 ［get_ports {ja［0］}］
##sch name = ja2
#set_property package_pin l2 ［get_ports {ja［1］}］
#set_property iostandard lvcmos33 ［get_ports {ja［1］}］
##sch name = ja3
#set_property package_pin j2 ［get_ports {ja［2］}］
#set_property iostandard lvcmos33 ［get_ports {ja［2］}］
##sch name = ja4
#set_property package_pin g2 ［get_ports {ja［3］}］
#set_property iostandard lvcmos33 ［get_ports {ja［3］}］
##sch name = ja7
#set_property package_pin h1 ［get_ports {ja［4］}］
#set_property iostandard lvcmos33 ［get_ports {ja［4］}］
##sch name = ja8
#set_property package_pin k2 ［get_ports {ja［5］}］
#set_property iostandard lvcmos33 ［get_ports {ja［5］}］
##sch name = ja9
#set_property package_pin h2 ［get_ports {ja［6］}］
#set_property iostandard lvcmos33 ［get_ports {ja［6］}］
##sch name = ja10
#set_property package_pin g3 ［get_ports {ja［7］}］
#set_property iostandard lvcmos33 ［get_ports {ja［7］}］
##pmod header jb
##sch name = jb1
#set_property package_pin a14 ［get_ports {jb［0］}］
#set_property iostandard lvcmos33 ［get_ports {jb［0］}］
##sch name = jb2
#set_property package_pin a16 ［get_ports {jb［1］}］
#set_property iostandard lvcmos33 ［get_ports {jb［1］}］
##sch name = jb3
#set_property package_pin b15 ［get_ports {jb［2］}］
#set_property iostandard lvcmos33 ［get_ports {jb［2］}］
##sch name = jb4
#set_property package_pin b16 ［get_ports {jb［3］}］
#set_property iostandard lvcmos33 ［get_ports {jb［3］}］
##sch name = jb7
#set_property package_pin a15 ［get_ports {jb［4］}］
#set_property iostandard lvcmos33 ［get_ports {jb［4］}］
##sch name = jb8
#set_property package_pin a17 ［get_ports {jb［5］}］
#set_property iostandard lvcmos33 ［get_ports {jb［5］}］
##sch name = jb9
#set_property package_pin c15 ［get_ports {jb［6］}］
#set_property iostandard lvcmos33 ［get_ports {jb［6］}］
##sch name = jb10
#set_property package_pin c16 ［get_ports {jb［7］}］
#set_property iostandard lvcmos33 ［get_ports {jb［7］}］
##pmod header jc
##sch name = jc1
#set_property package_pin k17 ［get_ports {jc［0］}］
#set_property iostandard lvcmos33 ［get_ports {jc［0］}］
##sch name = jc2
#set_property package_pin m18 ［get_ports {jc［1］}］
#set_property iostandard lvcmos33 ［get_ports {jc［1］}］
##sch name = jc3
#set_property package_pin n17 ［get_ports {jc［2］}］
#set_property iostandard lvcmos33 ［get_ports {jc［2］}］
##sch name = jc4
#set_property package_pin p18 ［get_ports {jc［3］}］
#set_property iostandard lvcmos33 ［get_ports {jc［3］}］
##sch name = jc7
#set_property package_pin l17 ［get_ports {jc［4］}］
#set_property iostandard lvcmos33 ［get_ports {jc［4］}］
##sch name = jc8
#set_property package_pin m19 ［get_ports {jc［5］}］
#set_property iostandard lvcmos33 ［get_ports {jc［5］}］
##sch name = jc9
#set_property package_pin p17 ［get_ports {jc［6］}］
#set_property iostandard lvcmos33 ［get_ports {jc［6］}］
##sch name = jc10
#set_property package_pin r18 ［get_ports {jc［7］}］
#set_property iostandard lvcmos33 ［get_ports {jc［7］}］
##pmod header jxadc
##sch name = xa1_p
#set_property package_pin j3 ［get_ports {jxadc［0］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［0］}］
##sch name = xa2_p
#set_property package_pin l3 ［get_ports {jxadc［1］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［1］}］
##sch name = xa3_p
#set_property package_pin m2 ［get_ports {jxadc［2］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［2］}］
##sch name = xa4_p
#set_property package_pin n2 ［get_ports {jxadc［3］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［3］}］
##sch name = xa1_n
#set_property package_pin k3 ［get_ports {jxadc［4］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［4］}］
##sch name = xa2_n
#set_property package_pin m3 ［get_ports {jxadc［5］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［5］}］
##sch name = xa3_n
#set_property package_pin m1 ［get_ports {jxadc［6］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［6］}］
##sch name = xa4_n
#set_property package_pin n1 ［get_ports {jxadc［7］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［7］}］
##vga connector
#set_property package_pin g19 ［get_ports {vgared［0］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［0］}］
#set_property package_pin h19 ［get_ports {vgared［1］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［1］}］
#set_property package_pin j19 ［get_ports {vgared［2］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［2］}］
#set_property package_pin n19 ［get_ports {vgared［3］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［3］}］
#set_property package_pin n18 ［get_ports {vgablue［0］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［0］}］
#set_property package_pin l18 ［get_ports {vgablue［1］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［1］}］
#set_property package_pin k18 ［get_ports {vgablue［2］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［2］}］
#set_property package_pin j18 ［get_ports {vgablue［3］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［3］}］
#set_property package_pin j17 ［get_ports {vgagreen［0］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［0］}］
#set_property package_pin h17 ［get_ports {vgagreen［1］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［1］}］
#set_property package_pin g17 ［get_ports {vgagreen［2］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［2］}］
#set_property package_pin d17 ［get_ports {vgagreen［3］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［3］}］
#set_property package_pin p19 ［get_ports hsync］
#set_property iostandard lvcmos33 ［get_ports hsync］
#set_property package_pin r19 ［get_ports vsync］
#set_property iostandard lvcmos33 ［get_ports vsync］
##usb-rs232 interface
#set_property package_pin b18 ［get_ports rsrx］
#set_property iostandard lvcmos33 ［get_ports rsrx］
#set_property package_pin a18 ［get_ports rstx］
#set_property iostandard lvcmos33 ［get_ports rstx］
##usb hid （ps/2）
#set_property package_pin c17 ［get_ports ps2clk］
#set_property iostandard lvcmos33 ［get_ports ps2clk］
#set_property pullup true ［get_ports ps2clk］
#set_property package_pin b17 ［get_ports ps2data］
#set_property iostandard lvcmos33 ［get_ports ps2data］
#set_property pullup true ［get_ports ps2data］
##quad spi flash
##note that cclk_0 cannot be placed in 7 series devices. you can access it using the
##startupe2 primitive.
#set_property package_pin d18 ［get_ports {qspidb［0］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［0］}］
#set_property package_pin d19 ［get_ports {qspidb［1］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［1］}］
#set_property package_pin g18 ［get_ports {qspidb［2］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［2］}］
#set_property package_pin f18 ［get_ports {qspidb［3］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［3］}］
#set_property package_pin k19 ［get_ports qspicsn］
#set_property iostandard lvcmos33 ［get_ports qspicsn］
AFG3000C系列任意函数发生器的功能特点及应用范围
中科英华铜箔产能将跻身世界前列
如何利用人工智能快速记下单词
开环增益的测量—电流注入法、不稳定系统的测量
ieee1588v2交换机简介
FPGA简单门电路怎么实现？
fireflyAIO-3288C主板--MaskRom模式的调整方法
大疆公司推出首款带变焦功能的无人机
销量猛涨，OPPO是如何逆袭华为的？原来是靠这个！
CoinAll上线Zeux（ZUC）全球首个数字货币支付理财APP
电子领域中电路板上屏蔽罩的作用
特斯拉再创历史 电动机入围国际发动机大奖
外资对MediaTek喊出500元的目标价，并看好MediaTek在5G领域的发展
软银42亿美元增持雅虎日本股份 动力电池商LG化学与SK Innovation诉讼
fireflyRK3399开发板介绍
嘉立创EDA如何布局圆形LED灯板
汇总各种流量计的工作原理
逃不过的双11「算法围城」需要时间同步
sdr技术原理解析
英国五个技术中心致力于使用AI来加快疾病诊断和改善
verilog实现反相器，2输入与门、2输入或门、2输入与非门、2输入或非门、2输入异或门、2输入同或门；
撰写仿真程序，对实现进行仿真测试；
将仿真后的verilog代码进行综合与实现，并下载到basys3上验证；
2. verilog实现2选1mux
撰写仿真程序，对其进行测试；
将仿真后的verilog代码进行综合与实现，并下载到basys3上验证；
2.
led［0］ sw［0］ sw［1］实现2输入与门
led［2］ sw［2］ sw［3］实现2输入或门
led［4］ sw［4］ sw［5］实现2输入与非门
led［6］ sw［6］ sw［7］实现2输入或非门
led［8］ sw［8］ sw［9］实现2输入异或门
led［10］ sw［10］ sw［11］实现2输入同或门
led［12］ sw［12］实现反相器
led［13］ sw［13］ sw［14］ sw［15］实现2选1mux
3.实现模块
module fpga001（
input ［15:0］ sw，
output ［13:0］ led
）;
assign led［0］ = sw［0］ & sw［1］;
assign led［2］ = sw［2］ | sw［3］;
assign led［4］ = ~（sw［4］ & sw［5］）;
assign led［6］ = ~（sw［6］ | sw［7］）;
assign led［8］ = （sw［8］ & （~sw［9］）） | （~sw［8］ & sw［9］）;
assign led［10］ = ~（（sw［10］ & （~sw［11］）） | （~sw［10］ & sw［11］））;
assign led［12］ = ~sw［12］;
assign led［13］ = ~sw［13］ & sw［14］ | sw［13］ & sw［15］;
endmodule
4.测试模块
module fd;
reg［15:0］ w;
wire［13:0］ l;
fpga001 f（w， l）;
initial
begin
w = 16‘b0;
#10 w = 16’b0010010101010101;
#10 w = 16‘b0101101010101010;
#10 w = 16’b0110010101010101;
#10 w = 16‘b1001101010101010;
#10 w = 16’b1010010101010101;
#10 w = 16‘b1111101010101010;
#20 $finish;
end
initial
begin
$monitor（$time， “led = %b”， w）;
end
endmodule
5.引脚分布图
## this file is a general .xdc for the basys3 rev b board
## to use it in a project：
## - uncomment the lines corresponding to used pins
## - rename the used ports （in each line， after get_ports） according to the top level signal names in the project
## clock signal
#set_property package_pin w5 ［get_ports clk］
#set_property iostandard lvcmos33 ［get_ports clk］
#create_clock -add -name sys_clk_pin -period 10.00 -waveform {0 5} ［get_ports clk］
## switches
set_property package_pin v17 ［get_ports {sw［0］}］
set_property iostandard lvcmos33 ［get_ports {sw［0］}］
set_property package_pin v16 ［get_ports {sw［1］}］
set_property iostandard lvcmos33 ［get_ports {sw［1］}］
set_property package_pin w16 ［get_ports {sw［2］}］
set_property iostandard lvcmos33 ［get_ports {sw［2］}］
set_property package_pin w17 ［get_ports {sw［3］}］
set_property iostandard lvcmos33 ［get_ports {sw［3］}］
set_property package_pin w15 ［get_ports {sw［4］}］
set_property iostandard lvcmos33 ［get_ports {sw［4］}］
set_property package_pin v15 ［get_ports {sw［5］}］
set_property iostandard lvcmos33 ［get_ports {sw［5］}］
set_property package_pin w14 ［get_ports {sw［6］}］
set_property iostandard lvcmos33 ［get_ports {sw［6］}］
set_property package_pin w13 ［get_ports {sw［7］}］
set_property iostandard lvcmos33 ［get_ports {sw［7］}］
set_property package_pin v2 ［get_ports {sw［8］}］
set_property iostandard lvcmos33 ［get_ports {sw［8］}］
set_property package_pin t3 ［get_ports {sw［9］}］
set_property iostandard lvcmos33 ［get_ports {sw［9］}］
set_property package_pin t2 ［get_ports {sw［10］}］
set_property iostandard lvcmos33 ［get_ports {sw［10］}］
set_property package_pin r3 ［get_ports {sw［11］}］
set_property iostandard lvcmos33 ［get_ports {sw［11］}］
set_property package_pin w2 ［get_ports {sw［12］}］
set_property iostandard lvcmos33 ［get_ports {sw［12］}］
set_property package_pin u1 ［get_ports {sw［13］}］
set_property iostandard lvcmos33 ［get_ports {sw［13］}］
set_property package_pin t1 ［get_ports {sw［14］}］
set_property iostandard lvcmos33 ［get_ports {sw［14］}］
set_property package_pin r2 ［get_ports {sw［15］}］
set_property iostandard lvcmos33 ［get_ports {sw［15］}］
## leds
set_property package_pin u16 ［get_ports {led［0］}］
set_property iostandard lvcmos33 ［get_ports {led［0］}］
set_property package_pin e19 ［get_ports {led［1］}］
set_property iostandard lvcmos33 ［get_ports {led［1］}］
set_property package_pin u19 ［get_ports {led［2］}］
set_property iostandard lvcmos33 ［get_ports {led［2］}］
set_property package_pin v19 ［get_ports {led［3］}］
set_property iostandard lvcmos33 ［get_ports {led［3］}］
set_property package_pin w18 ［get_ports {led［4］}］
set_property iostandard lvcmos33 ［get_ports {led［4］}］
set_property package_pin u15 ［get_ports {led［5］}］
set_property iostandard lvcmos33 ［get_ports {led［5］}］
set_property package_pin u14 ［get_ports {led［6］}］
set_property iostandard lvcmos33 ［get_ports {led［6］}］
set_property package_pin v14 ［get_ports {led［7］}］
set_property iostandard lvcmos33 ［get_ports {led［7］}］
set_property package_pin v13 ［get_ports {led［8］}］
set_property iostandard lvcmos33 ［get_ports {led［8］}］
set_property package_pin v3 ［get_ports {led［9］}］
set_property iostandard lvcmos33 ［get_ports {led［9］}］
set_property package_pin w3 ［get_ports {led［10］}］
set_property iostandard lvcmos33 ［get_ports {led［10］}］
set_property package_pin u3 ［get_ports {led［11］}］
set_property iostandard lvcmos33 ［get_ports {led［11］}］
set_property package_pin p3 ［get_ports {led［12］}］
set_property iostandard lvcmos33 ［get_ports {led［12］}］
set_property package_pin n3 ［get_ports {led［13］}］
set_property iostandard lvcmos33 ［get_ports {led［13］}］
set_property package_pin p1 ［get_ports {led［14］}］
set_property iostandard lvcmos33 ［get_ports {led［14］}］
set_property package_pin l1 ［get_ports {led［15］}］
set_property iostandard lvcmos33 ［get_ports {led［15］}］
##7 segment display
#set_property package_pin w7 ［get_ports {seg［0］}］
#set_property iostandard lvcmos33 ［get_ports {seg［0］}］
#set_property package_pin w6 ［get_ports {seg［1］}］
#set_property iostandard lvcmos33 ［get_ports {seg［1］}］
#set_property package_pin u8 ［get_ports {seg［2］}］
#set_property iostandard lvcmos33 ［get_ports {seg［2］}］
#set_property package_pin v8 ［get_ports {seg［3］}］
#set_property iostandard lvcmos33 ［get_ports {seg［3］}］
#set_property package_pin u5 ［get_ports {seg［4］}］
#set_property iostandard lvcmos33 ［get_ports {seg［4］}］
#set_property package_pin v5 ［get_ports {seg［5］}］
#set_property iostandard lvcmos33 ［get_ports {seg［5］}］
#set_property package_pin u7 ［get_ports {seg［6］}］
#set_property iostandard lvcmos33 ［get_ports {seg［6］}］
#set_property package_pin v7 ［get_ports dp］
#set_property iostandard lvcmos33 ［get_ports dp］
#set_property package_pin u2 ［get_ports {an［0］}］
#set_property iostandard lvcmos33 ［get_ports {an［0］}］
#set_property package_pin u4 ［get_ports {an［1］}］
#set_property iostandard lvcmos33 ［get_ports {an［1］}］
#set_property package_pin v4 ［get_ports {an［2］}］
#set_property iostandard lvcmos33 ［get_ports {an［2］}］
#set_property package_pin w4 ［get_ports {an［3］}］
#set_property iostandard lvcmos33 ［get_ports {an［3］}］
##buttons
#set_property package_pin u18 ［get_ports btnc］
#set_property iostandard lvcmos33 ［get_ports btnc］
#set_property package_pin t18 ［get_ports btnu］
#set_property iostandard lvcmos33 ［get_ports btnu］
#set_property package_pin w19 ［get_ports btnl］
#set_property iostandard lvcmos33 ［get_ports btnl］
#set_property package_pin t17 ［get_ports btnr］
#set_property iostandard lvcmos33 ［get_ports btnr］
#set_property package_pin u17 ［get_ports btnd］
#set_property iostandard lvcmos33 ［get_ports btnd］
##pmod header ja
##sch name = ja1
#set_property package_pin j1 ［get_ports {ja［0］}］
#set_property iostandard lvcmos33 ［get_ports {ja［0］}］
##sch name = ja2
#set_property package_pin l2 ［get_ports {ja［1］}］
#set_property iostandard lvcmos33 ［get_ports {ja［1］}］
##sch name = ja3
#set_property package_pin j2 ［get_ports {ja［2］}］
#set_property iostandard lvcmos33 ［get_ports {ja［2］}］
##sch name = ja4
#set_property package_pin g2 ［get_ports {ja［3］}］
#set_property iostandard lvcmos33 ［get_ports {ja［3］}］
##sch name = ja7
#set_property package_pin h1 ［get_ports {ja［4］}］
#set_property iostandard lvcmos33 ［get_ports {ja［4］}］
##sch name = ja8
#set_property package_pin k2 ［get_ports {ja［5］}］
#set_property iostandard lvcmos33 ［get_ports {ja［5］}］
##sch name = ja9
#set_property package_pin h2 ［get_ports {ja［6］}］
#set_property iostandard lvcmos33 ［get_ports {ja［6］}］
##sch name = ja10
#set_property package_pin g3 ［get_ports {ja［7］}］
#set_property iostandard lvcmos33 ［get_ports {ja［7］}］
##pmod header jb
##sch name = jb1
#set_property package_pin a14 ［get_ports {jb［0］}］
#set_property iostandard lvcmos33 ［get_ports {jb［0］}］
##sch name = jb2
#set_property package_pin a16 ［get_ports {jb［1］}］
#set_property iostandard lvcmos33 ［get_ports {jb［1］}］
##sch name = jb3
#set_property package_pin b15 ［get_ports {jb［2］}］
#set_property iostandard lvcmos33 ［get_ports {jb［2］}］
##sch name = jb4
#set_property package_pin b16 ［get_ports {jb［3］}］
#set_property iostandard lvcmos33 ［get_ports {jb［3］}］
##sch name = jb7
#set_property package_pin a15 ［get_ports {jb［4］}］
#set_property iostandard lvcmos33 ［get_ports {jb［4］}］
##sch name = jb8
#set_property package_pin a17 ［get_ports {jb［5］}］
#set_property iostandard lvcmos33 ［get_ports {jb［5］}］
##sch name = jb9
#set_property package_pin c15 ［get_ports {jb［6］}］
#set_property iostandard lvcmos33 ［get_ports {jb［6］}］
##sch name = jb10
#set_property package_pin c16 ［get_ports {jb［7］}］
#set_property iostandard lvcmos33 ［get_ports {jb［7］}］
##pmod header jc
##sch name = jc1
#set_property package_pin k17 ［get_ports {jc［0］}］
#set_property iostandard lvcmos33 ［get_ports {jc［0］}］
##sch name = jc2
#set_property package_pin m18 ［get_ports {jc［1］}］
#set_property iostandard lvcmos33 ［get_ports {jc［1］}］
##sch name = jc3
#set_property package_pin n17 ［get_ports {jc［2］}］
#set_property iostandard lvcmos33 ［get_ports {jc［2］}］
##sch name = jc4
#set_property package_pin p18 ［get_ports {jc［3］}］
#set_property iostandard lvcmos33 ［get_ports {jc［3］}］
##sch name = jc7
#set_property package_pin l17 ［get_ports {jc［4］}］
#set_property iostandard lvcmos33 ［get_ports {jc［4］}］
##sch name = jc8
#set_property package_pin m19 ［get_ports {jc［5］}］
#set_property iostandard lvcmos33 ［get_ports {jc［5］}］
##sch name = jc9
#set_property package_pin p17 ［get_ports {jc［6］}］
#set_property iostandard lvcmos33 ［get_ports {jc［6］}］
##sch name = jc10
#set_property package_pin r18 ［get_ports {jc［7］}］
#set_property iostandard lvcmos33 ［get_ports {jc［7］}］
##pmod header jxadc
##sch name = xa1_p
#set_property package_pin j3 ［get_ports {jxadc［0］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［0］}］
##sch name = xa2_p
#set_property package_pin l3 ［get_ports {jxadc［1］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［1］}］
##sch name = xa3_p
#set_property package_pin m2 ［get_ports {jxadc［2］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［2］}］
##sch name = xa4_p
#set_property package_pin n2 ［get_ports {jxadc［3］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［3］}］
##sch name = xa1_n
#set_property package_pin k3 ［get_ports {jxadc［4］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［4］}］
##sch name = xa2_n
#set_property package_pin m3 ［get_ports {jxadc［5］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［5］}］
##sch name = xa3_n
#set_property package_pin m1 ［get_ports {jxadc［6］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［6］}］
##sch name = xa4_n
#set_property package_pin n1 ［get_ports {jxadc［7］}］
#set_property iostandard lvcmos33 ［get_ports {jxadc［7］}］
##vga connector
#set_property package_pin g19 ［get_ports {vgared［0］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［0］}］
#set_property package_pin h19 ［get_ports {vgared［1］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［1］}］
#set_property package_pin j19 ［get_ports {vgared［2］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［2］}］
#set_property package_pin n19 ［get_ports {vgared［3］}］
#set_property iostandard lvcmos33 ［get_ports {vgared［3］}］
#set_property package_pin n18 ［get_ports {vgablue［0］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［0］}］
#set_property package_pin l18 ［get_ports {vgablue［1］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［1］}］
#set_property package_pin k18 ［get_ports {vgablue［2］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［2］}］
#set_property package_pin j18 ［get_ports {vgablue［3］}］
#set_property iostandard lvcmos33 ［get_ports {vgablue［3］}］
#set_property package_pin j17 ［get_ports {vgagreen［0］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［0］}］
#set_property package_pin h17 ［get_ports {vgagreen［1］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［1］}］
#set_property package_pin g17 ［get_ports {vgagreen［2］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［2］}］
#set_property package_pin d17 ［get_ports {vgagreen［3］}］
#set_property iostandard lvcmos33 ［get_ports {vgagreen［3］}］
#set_property package_pin p19 ［get_ports hsync］
#set_property iostandard lvcmos33 ［get_ports hsync］
#set_property package_pin r19 ［get_ports vsync］
#set_property iostandard lvcmos33 ［get_ports vsync］
##usb-rs232 interface
#set_property package_pin b18 ［get_ports rsrx］
#set_property iostandard lvcmos33 ［get_ports rsrx］
#set_property package_pin a18 ［get_ports rstx］
#set_property iostandard lvcmos33 ［get_ports rstx］
##usb hid （ps/2）
#set_property package_pin c17 ［get_ports ps2clk］
#set_property iostandard lvcmos33 ［get_ports ps2clk］
#set_property pullup true ［get_ports ps2clk］
#set_property package_pin b17 ［get_ports ps2data］
#set_property iostandard lvcmos33 ［get_ports ps2data］
#set_property pullup true ［get_ports ps2data］
##quad spi flash
##note that cclk_0 cannot be placed in 7 series devices. you can access it using the
##startupe2 primitive.
#set_property package_pin d18 ［get_ports {qspidb［0］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［0］}］
#set_property package_pin d19 ［get_ports {qspidb［1］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［1］}］
#set_property package_pin g18 ［get_ports {qspidb［2］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［2］}］
#set_property package_pin f18 ［get_ports {qspidb［3］}］
#set_property iostandard lvcmos33 ［get_ports {qspidb［3］}］
#set_property package_pin k19 ［get_ports qspicsn］
#set_property iostandard lvcmos33 ［get_ports qspicsn］
AFG3000C系列任意函数发生器的功能特点及应用范围
中科英华铜箔产能将跻身世界前列
如何利用人工智能快速记下单词
开环增益的测量—电流注入法、不稳定系统的测量
ieee1588v2交换机简介
FPGA简单门电路怎么实现？
fireflyAIO-3288C主板--MaskRom模式的调整方法
大疆公司推出首款带变焦功能的无人机
销量猛涨，OPPO是如何逆袭华为的？原来是靠这个！
CoinAll上线Zeux（ZUC）全球首个数字货币支付理财APP
电子领域中电路板上屏蔽罩的作用
特斯拉再创历史 电动机入围国际发动机大奖
外资对MediaTek喊出500元的目标价，并看好MediaTek在5G领域的发展
软银42亿美元增持雅虎日本股份 动力电池商LG化学与SK Innovation诉讼
fireflyRK3399开发板介绍
嘉立创EDA如何布局圆形LED灯板
汇总各种流量计的工作原理
逃不过的双11「算法围城」需要时间同步
sdr技术原理解析
英国五个技术中心致力于使用AI来加快疾病诊断和改善